WS-X45-SUP7-E, the Cisco Catalyst 4500E supervisor engine 7-E, is the leading borderless networks access and aggregation supervisor engine for the Cisco Catalyst 4500E series. Supervisor Engine7-E delivers high-performance aggregation deployments with increasing Gigabit Ethernet and 10G Ethernet fiber density along with hardware capabilities to support enterprise-level aggregation functions.
WS-X45-SUP7-E Specification |
|
| Chassis compatibility | All Catalyst 4500 E-series switches |
| Software requirements (minimum) | Refer to your software release notes for the latest software release requirements |
| Chassis slot restrictions | •Catalyst 4503-E: Slot 1 only
•Catalyst 4506-E: Slot 1 only •Catalyst 4507R-E and Catalyst 4507R+E: Slot 3 and slot 4 •Catalyst 4510R-E and Catalyst 4510R+E: Slot 5 and slot 6 |
| Bandwidth per slot | 48-Gbps |
| Memory | 2-GB (upgrade to 4-GB) |
| STATUS LED | The status LED indicates the current health of the supervisor engine and the current software state. |
| RESET switch | The RESET switch is used to reset and restart the switch.
Note Use a paper clip or other small, pointed object to press the RESET switch. |
| ACTIVE SUP LED | The active supervisor engine LED indicates whether the supervisor engine is active or in standby mode in redundant supervisor engine configurations. |
| UTILIZATION LEDs | Eight LEDs indicate (as an approximate percentage) the current traffic load over the backplane. |
| USB connectors | Two USB 2.0 ports are provided. Port 1 operates in device mode (upstream) and port 2 in host mode (downstream). Port 1 has a standard Type B USB connector and can be used as a USB console.Port 2 has a USB type A connector and a standard USB 2.0 device like a flash memory device can plug into this connector. |
| SECURE DIGITAL slot | A standard Secure Data (SD) memory card interface is provided on the front panel |
| CONSOLE port | This is a 10/100/1000 port that uses an RJ-45 connector. The console port allows you th access the switch either locally (with a console terminal) has an RJ-45 connector. The console port allows you to perform the following functions:
•Configure the switch from the CLI •Monitor network statistics and errors •Configure SNMP agent parameters |
| 10/100/1000 MGT port | The Ethernet management port is a Layer 3 host port to which you can connect a PC. You can use the Ethernet management port instead of the switch console port for network management. When managing a switch, connect the PC to the Ethernet management port on a Catalyst 4500 E-series switch.
Note When connecting a PC to the Ethernet management port, you must assign an IP address. |
| LINK LED | The 10/100/1000 MGT port has a link LED associated with it. |
| 1G/10G UPLINKS (SFP/SFP+) ports | The Supervisor Engine 7-E has four 1-G or 10-G ports that use either SFP transceivers or SFP+ transceivers. |
| Uplink port LEDs | Each of the four uplink ports has two LEDs associated with it. One LED displays port status when a 1-GB SFP transceiver is installed in the port socket. The second LED displays uplink port status when a 10-GB SFP+ transceiver is installed in the port socket. |
| Power requirement | 302 W |
| Operating temperature | Certified for operation: 32° to 104°F (0° to 40°C)
•Designed and tested for operation: 32° to 130°F (0° to 55°C) |
| Humidity (RH) ambient (noncondensing) | 10 to 90% |
| Operating altitude | Certified for operation: 0 to 6500 ft (0 to 2000 m)
•Designed and tested for operation: -200 to 10,000 ft (-60 to 3000 m) |
| Operating temperature | Certified for operation: 32° to 104°F (0° to 40°C)
•Designed and tested for operation: 32° to 130°F (0° to 55°C) |
